Mar. 18th, 2017

Shaak Ti?

Mar. 18th, 2017 08:14 pm
glittersweet: (Default)

So having practiced so many times with my Ahsoka molds, and previous methods with Shaak Ti.. I may actually be able to use what I have learnt with Ahsoka to use my Shaak Ti molds again 🙂



(Photo above: metal shelves with cement molds of different sizes, bottom shelf supporting in particular the two part molds for Ahsoka Tano and Shaak Ti creature effects.)


This is very exciting. To find a method that creates a predictable latex cast, that is durable and light. I think I may need to do a video guide as if takes both hands, well full body, and is so messy it would ruin my camera equipment to try and get photos.


But it winds up cheaper than a purely slush cast piece with about the same flex and is lighter. I still need to test if the support I used for Shaak Ti will work with this new method, but I do have hope.



(photo above: two part molds resting against a white wall and on grass with exposed topsoil.)


The cast has also not pulled from the molds as much as previous which means it is likely to shrink less. While these molds were relatively easy to work with it may prove more troublesome with the Shaak Ti molds as there are more ridges. But these are exactly why I want to keep using this method- the ridges tend to cause latex to clump into deeper parts of the mold and crete weak thin casts over the higher parts.


Tomorrow I will test it.


This method may also work for Turian jaws and mask 🙂 Right now the flat back cast for the jaws work very nicely.


 

glittersweet: (Default)

I don’t like to use patterns, I find infinitely more success with drafting (more than drafting, and drafting more successful than using an existing pattern.) It has everything to do with modern pattern blocks. In general bodies vary each generation but there is a fashionable shape as well as a fashionable size.


My shape goes against modern fit models in a way that does not conform to the methods of correcting a pattern.



(photos above- three mannequin torsos on narrow stands stood side by side to illustrate differences in shape despite being set to the same size. The mannequin on the left of each photo  is covered in white cloth and is not adjustable, the mannequin in the centre is adjustable but is narrower across the chest/waist/hips, but wider in profile, the mannequin to the right is much rounder in all directions and has a much rounder upper back with the armscyes set further forward.


Once again these three mannequins show the different fashion shapes.


Why is this important for Mon Mothma? Isn’t it just a robe?


Nope! She has Raglan sleeves, with four seams each sleeve! Her robes have semi-princess seams (they do not cross the bust point but do terminate in the armscye.)


I do collect vintage patterns when I find useful ones however. Or useful to me 🙂



(photo above: a vintage pattern from the 1970s, three women in different variations of the same garment- all with full lower sleeves, semi fitted through the body, and flared skirts)


The dress is unfortunately four panels but has the raglan sleeve to a closed neck 🙂 And bishop sleeves.


The samples are actually much more true than I am used to so I did add too much extra SA when transferring but here is how I did it:



(Photos above: three stages of a pattern alteration, description in following text.)


I transferred all patterns to brown paper. I traces each pattern a short distance from the edge of the paper to allow the paper to be folded straight whereas in the original pattern the dress panels all tapered in to the waist and out to the hem.


For the front dress panel I first drew and then cut a semi princess shape from the front. This left a much narrower side front than I wanted, but the front needed no more work.


I then used double sided tape to stick the outer side of the new side piece to a length of narrow brown paper. I then flared that side seam out about 20cm at the hem and tapered it to the waist.


I repeated on the inside of the side panel.


Now the patter for the dress front has a side seam and a much fuller hem.


I repeated this for the back panels and the sleeves.



(Photo above: traced sleeve pattern on brown paper, parallel lines to divide the pattern into four.)


 


Since then I have cut the shell fabric and a stabilising lining. The lining is a loosely woven fabric to allow airflow when worn.


I overestimated my seam allowances. The next step will be to assemble this on the form that is going to most easily allow for a semi loose fit but also allow for shoulder shaping. So I shall use the non adjustable mannequin as it has curved upper shoulders at least.

Profile

glittersweet: (Default)
pinkdiamond

June 2024

S M T W T F S
      1
2345678
9101112131415
16171819202122
23242526272829
30      

Most Popular Tags

Style Credit

Expand Cut Tags

No cut tags
Powered by Dreamwidth Studios